外文翻译--车床上料机械手设计.doc

《外文翻译--车床上料机械手设计.doc》由会员分享，可在线阅读，更多相关《外文翻译--车床上料机械手设计.doc（23页珍藏版）》请在沃文网上搜索。

1、本科毕业设计(论文)外文翻译（附外文原文） 学 院： 机械与控制工程 课题名称： 车床上料机械手设计 专业(方向)： 机械设计制造及其自动化 22外文原文：Mechanical and control system for ManipulatorsAbstract: Recently, in the world with a clip or a hand robot system has been developed, a variety of methods is applied on the, quasi humanized and non-personification. Not onl

2、y the mechanical structure of these systems is investigated, but also the necessary control system is also included. As the staff, these robots can use their hands to grasp different objects, without changing the clip. These manipulators possess special athletic abilities (such as small mass and ine

3、rtia), which enable the object to be more complex and more precise in the work of robot manipulators. These complex operations are grasped around arbitrary angle and axis rotation. This paper outlines the general design of this manipulator, and gives a sample of such manipulators, such as the Karlsr

4、uhe smart hand. At the end of this paper, some new ideas are introduced, such as the use of liquid actuators for humanoid robot design a brand new robot manipulator.Keywords: multi robot manipulator; robot hand; finishing operation; mechanical system; control system1 .IntroductionIn June 2001 in Kar

5、lsruhe, Germany to carry out special study a humanoid robot, in order to develop in a normal environment (such as kitchen or the living room) and human cooperation and interaction of the robot system. The design of these robots is designed to help us capture objects of size, shape and weight in a no

6、n -professional, non - industrial condition, such as in many objects. At the same time, they must be able to manipulate the object very well. This flexibility can only be through a strong adaptability of robot hand grasping system to obtain, that is, the so-called multi refers to the robot or robot

7、hand.The research project mentioned above is to create a humanoid robot, which will equip this robot hand system. This novice will be produced by two organizations, which are IPR (process control and Robotics Research Institute) and C (Computer Science Institute), University of Karlsruhe. These two

8、organizations have the experience of making such systems, but slightly different views.IPR made Karlsruhe dexterous hand II (as shown in Figure 1), is a four finger gripper is independent of each other, we will be introduced in detail in this paper. The hand made by IAI (as shown in Figure 17) is us

9、ed as prosthetic for the disabled. Figure 1.IPR Karlsruhe smart hand Figure 2 fluid hand developed by IAI2 .general structure of robot handA robot hand can be divided into two major subsystems: mechanical systems and control systems.The mechanical system can be divided into the structure design, the

10、 drive system and the sensor system, we will further introduce in the third part. In the fourth part of the introduction of the control system at least by the control of hardware and software components.We will be on the two system problems of a basic introduction, and then use the Karlsruhe dextero

11、us hand II demonstration.3 .Mechanical SystemsThe mechanical system will describe how the hand looks and what components. It determines the structure design, the number of fingers and the use of materials. In addition, the position of the actuator (such as the motor) and the sensor (e.g. position en

12、coder) is also determined.3.1 structure designThe structure design will have the very important function to the manipulators flexibility, namely it can grasp which kind of object and can carry on to the object to carry on what kind of operation. When designing a robot hand, three basic elements must

13、 be determined: the number of fingers, the number of fingers, the size and placement of the fingers.In order to crawl and operate the object safely within the manipulator, at least three fingers. In order to operate the object being grasped for 6 degrees of freedom (3 translational and 3 rotational

14、degrees of freedom), each finger must have 3 separate joints. This method was used in the first generation of Karlsruhes smart hand. However, in order to catch an object without the need to release it first to pick up, at least 4 fingers.Two methods: the human and the non - human are to determine th

15、e size and placement of the finger. Then it will depend on the object and the type of operation to which the desired operation is selected. It is easy to transfer grasping intention from hand to robot hand. However, the placement of different sizes and asymmetric positions of each finger will increa

16、se the processing cost, and it is the control system becoming more complicated, because each finger must be controlled separately. For the symmetrical arrangement of identical fingers, often using a non-anthropomorphic approach. Because only need to process and construct a single finger module, it c

17、an reduce the processing cost, but also the control system is simplified.3.2 drive systemThe flexibility of the actuator is also greatly affected by the drive of the joints, because it determines the potential strength, precision and speed of the joint movement. Two aspects of the mechanical movemen

18、t need to be considered: the movement source and the movement direction. In this case, there are several different methods, such as the paper 3, which can be produced by hydraulic cylinders or pneumatic cylinders, or, as most of the case, the motor is used. In most cases, motor drive, such as motor

19、too big and not directly associated with the corresponding finger joint together. Therefore, the movement must by the driver (usually located on the machine arm last connection point) transferred. There are several ways to realize this movement, such as the use of keys, the drive belt and the active

20、 axis. Using the indirect drive method of finger joint, more or less reduces the strength and accuracy of the whole system, and at the same time, the control system is complicated, because of different joint of each finger is often mechanically even together, but in the software of the control syste

21、m but are respectively independent control. Because of these shortcomings, the direct fusion of the small motor drive and the knuckle is quite necessary.3.3 sensing systemThe sensing system of the robot hand can transfer the feedback information from the hardware to the control software. It is neces

22、sary to establish a closed loop control for finger or object. 3 types of sensors were used in the machine.1）Hand state sensors determine the position of fingertip and finger joint and finger force situation. Know the precise position of the fingertips will make precise control possible. In addition,

23、 knowing that the finger is the force that is grasped at the object, you can grab a fragile object without breaking it.2）The grasping state sensor provides the contact information between the finger and the object. This kind of tactile information can be determined in the process of grasping the fir

24、st contact with the object in time, and can also avoid incorrect grasping, such as the edge and tip of the object. It can also detect whether the object has been caught, so as to avoid the object due to fall and damage.3）The object or pose sensor is used to determine the shape, position and directio

25、n of the object in a finger. This sensor is very essential if it is not clear to the case of the object. If this sensor can also act on the object that has been grasped, it can also control the pose (position and direction) of the object, thus monitoring whether or not.Depending on the drive system,

26、 the geometrical information about the joint position can be measured at a motion drive or directly at the joint. For example, if there is a rigid shaft coupling between the motor and the knuckle, then the position of the joint can be measured by a motor shaft (before the gear or after the gear). Ho

27、wever, if this coupling stiffness is not enough or to get a high accuracy, it can not use this method.3.4 the mechanical system of the robot hand in KarlsruheIn order to obtain more complex operation such as heavy grasping, the Karlsruhe smart hand II (KDH II) is composed of 4 fingers, and each fing

28、er is composed of 3 independent joints. The hand is designed for applications in industrial environments (Figure 3) and a control box, cylinder and screw nut and other objects. Therefore, we selected four identical fingers. They are symmetric, non-anthropomorphic configuration and each finger can ro

29、tate 90 DEG (Fig. 4).View from the first generation of Karlsruhe dexterous hand design by experience, for example, the problem of mechanical caused by the drive belts and larger friction factor leading to the control problem of Karlsruhe dexterous hand II uses a number of different design decisions.

30、 The DC motor between the joint 2 and the joint of each finger is integrated into the anterior part of the finger (Figure 5).This arrangement can be used with hard ball gears to transmit motion to the joints of the fingers. In the motor shaft angle encoder (before the gear) can be used as a high pre

31、cision position sensor. Figure 3 KDH II on industrial robot Figure 4 KDH II top view In order to perception of the role of finger force on the object, we invented a six axis force torque sensor (Figure 6). The sensor can be used as a fingertip for the end of a finger and is equipped with a spherical

32、 fingertip. It can grab lighter objects, but also can grab 3-5kg similar heavier objects. This sensor can measure the force of the direction of X, Y and Z and the torque of the winding axis. In addition, the laser triangulation sensor 3 collinear is placed in the hands of KDH II (Figure 5). Because

33、there are 3 such sensors, therefore not only can measure the distance between 3 single points, if you know the shape of the object, but also can detect the distance between the object surface and direction. The working frequency of the object state sensor is 1kHz, which can detect and avoid the slid

34、e of the object Figure 5 KDH II side view. Figure six a 6 degree of freedom torsion sensor with a strain gage sensor4 control systemThe robots control system determines which potential dexterity skills can actually be used, and those skills are provided by mechanical systems. As mentioned before, th

35、e control system can be divided into the control computer, namely, the hardware and the control algorithm is the software.The control system must meet the following conditions:1) Must have sufficient input and output ports. For example, a low level hand with 9 degrees of freedom, its drive needs at

36、least 9 way to simulate the output port, and there are 9 paths from the angle encoder input port. Such as force sensor, tactile sensor and object sensor, then port number will be increased by several times.2) The ability to have a quick and real-time response to external events. For example, when th

37、e detected object falls, the corresponding measures can be taken immediately.3) With a higher computational power to address some of the different tasks. Such as path planning, coordinate conversion, and closed-loop control for multi - object and object - parallel execution.4) The volume of the cont

38、rol system is small so that it can be integrated directly into the operating system.5) In the control system and between the drive and sensor must be electrically short. Especially for the sensor, if there is no word, a lot of interference will interfere with the sensor signal.4.1 control hardwareIn

39、 order to meet the requirements of the system, the hardware is distributed in several special processors. The controller can be easily integrated into the operating system, such as the low input output interface (motor and sensor), which is handled by a simple microcontroller. However, the higher le

40、vel of the control port requires a higher computing power, and a flexible real-time operating system is needed. This can be easily resolved through the PC.Therefore, the control hardware is often composed of a distributed computer system, which is a microcontroller, and the other is a powerful proce

41、ssor. Different computing units are connected by a communication system, such as bus system.4.2 control softwareRobot hand control software is quite complex. Must be real-time and parallel control of the fingers, but also plan the new trajectory of the fingers and objects. Therefore, in order to red

42、uce the complexity of the problem, it is necessary to divide this problem into several sub problems to deal with.On the other hand, software development. Robot hand is a research project, its programming environment such as user interface, programming tools and debugging facilities must be very stro

43、ng and flexible. These can only be met using a standard operating system. The hierarchical control system method is widely used in the robot after pruning, in order to meet the special requirements of the manipulator control.4.3 control system of the robot hand in KarlsruheAs said in Section 4.1, a

44、distributed method (Figure 7) is adopted for the hardware of the control hardware of the smart hand of Karlsruhe. A microcontroller controls a finger drive and sensor respectively, and a microcontroller is used to control the object state sensor (laser triangulation). These microcontrollers (Figure

45、7 the left and right side of the box) are directly mounted on the hand, so the shorter electrical connection between the driver and the sensor can be guaranteed. These microcontrollers are connected with the master computer and the master computer. This master computer (Figure 8, gray box in Figure

46、7) is a parallel computer composed of six industrial computers. These computers are arranged in a two-dimensional plane. Adjacent computer module (a computer with up to 8 adjacent modules) using the dual port RAM for rapid communication (Figure 7, the dark gray box). A computer used to control a fin

47、ger. Another is used to control the position between the object sensor and the object. The rest of the computer is safely around the computer as mentioned above. These computers are used to coordinate the entire control system. The structure of the control software reflects the architecture of the c

48、ontrol hardware. As shown in Figure 9. Figure 7 II KDH control hardware architecture Figure 8 parallel master computer for controlling II KDHA three maximum levels of online planning regarding this hand control system are being planned. The ideal object displacement command can be obtained by the superior robot control system and can be used as the precise programming of the object path. According to the target path, the feasible fetching behavior of the finger can be planned (the feasible grasping position of the object) is feasible. Now