毕业设计外文翻译-基于MATLAB的TD-SCDMA通信系统的调制与解调仿真程序设计.docx

《毕业设计外文翻译-基于MATLAB的TD-SCDMA通信系统的调制与解调仿真程序设计.docx》由会员分享，可在线阅读，更多相关《毕业设计外文翻译-基于MATLAB的TD-SCDMA通信系统的调制与解调仿真程序设计.docx（14页珍藏版）》请在沃文网上搜索。

1、Review of UMTS1.1 UMTS Network Architecture The European/Japanese 3G standard is referred to as UMTS. UMTS is one of a number of standards ratified by the ITU-T under the umbrella of IMT-2000. It is currently the dominant standard, with the US CDMA2000 standard gaining ground, particularly with oper

2、ators that have deployed cdmaOne as their 2G technology. At time of writing,Japan is the most advanced in terms of 3G network deployment. The three incumbent operators there have implemented three different technologies: J-Phone is using UMTS,KDDI has a CDMA2000 network, and the largest operator NTT

3、 DoCoMo is using a system branded as FOMA (Freedom of Multimedia Access). FOMA is based on the original UMTS proposal, prior to its harmonization and standardization.The UMTS standard is specified as a migration from the second generation GSM standard to UMTS via the General Packet Radio System (GPR

4、S) and Enhanced Data for Global Evolution (EDGE), as shown in Figure. This is a sound rationale since as of April 2003, there were over 847 Million GSM subscribers worldwide1, accounting for68% of the global cellular subscriber figures. The emphasis is on keeping as much of the GSM network as possib

5、le to operate with the new system.We are now well on the road towards Third Generation (3G), where the network will support all traffic types: voice, video and data, and we should see an eventual explosion in the services available on the mobile device. The driving technology for this is the IP prot

6、ocol. Many cellular operators are now at a position referred to as 2.5G, with the deployment of GPRS, which introduces an IP backbone into the mobile core network.The diagram below, Figure 2, shows an overview of the key components in a GPRS network, and how it fits into the existing GSM infrastruct

7、ure.The interface between the SGSN and GGSN is known as the Gn interface and uses the GPRS tunneling protocol (GTP, discussed later). The primary reason for the introduction of this infrastructure is to offer connections to external packet networks, such as the Internet or a corporate Intranet.This

8、brings the IP protocol into the network as a transport between the SGSN and GGSN. This allows data services such as email or web browsing on the mobile device,with users being charged based on volume of data rather than time connected.The dominant standard for delivery of 3G networks and services is

9、 the Universal Mobile Telecommunications System, or UMTS. The first deployment of UMTS is the Release 99 architecture, shown below in Figure 3.In this network, the major change is in the radio access network (RAN) with the introduction of CDMA technology for the air interface, and ATM as a transport

10、 in the transmission part. These changes have been introduced principally to support the transport of voice, video and data services on the same network. The core network remains relatively unchanged, with primarily software upgrades. However, the IP protocol pushes further into the network with the

11、 RNC now communicating with the 3G SGSN using IP.The next evolution step is the Release 4 architecture, Figure 4. Here, the GSM core is replaced with an IP network infrastructure based around Voice over IP technology.The MSC evolves into two separate components: a Media Gateway (MGW) and an MSC Serv

12、er (MSS). This essentially breaks apart the roles of connection and connection control. An MSS can handle multiple MGWs, making the network more scaleable.Since there are now a number of IP clouds in the 3G network, it makes sense to merge these together into one IP or IP/ATM backbone (it is likely

13、both options will be available to operators.) This extends IP right across the whole network, all the way to the BTS.This is referred to as the All-IP network, or the Release 5 architecture, as shown in Figure 5. The HLR/VLR/EIR are generalised and referred to as the HLR Subsystem(HSS).Now the last

14、remnants of traditional telecommunications switching are removed, leaving a network operating completely on the IP protocol, and generalised for the transport of many service types. Real-time services are supported through the introduction of a new network domain, the IP Multimedia Subsystem (IMS).C

15、urrently the 3GPP are working on Release 6, which purports to cover all aspects not addressed in frozen releases. Some call UMTS Release 6 4G and it includes such issues as interworking of hot spot radio access technologies such as wireless LAN1.2 UMTS FDD and TDDLike any CDMA system, UMTS needs a w

16、ide frequency band in which to operate to effectively spread signals. The defining characteristic of the system is the chip rate, where a chip is the width of one symbol of the CDMA code. UMTS uses a chip rate of 3.84Mchips/s and this converts to a required spectrum carrier of 5MHz wide. Since this

17、is wider than the 1.25MHz needed for the existing cdmaOne system, the UMTS air interface is termed wideband CDMA.There are actually two radio technologies under the UMTS umbrella: UMTS FDD and TDD. FDD stands for Frequency Division Duplex, and like GSM, separates traffic in the uplink and downlink b

18、y placing them at different frequency channels. Therefore an operator must have a pair of frequencies allocated to allow them to run a network, hence the term paired spectrum. TDD or Time Division Duplex requires only one frequency channel, and uplink and downlink traffic are separated by sending th

19、em at different times. The ITU-T spectrum usage, as shown in Figure 6, for FDD is 1920- 980MHz for uplink traffic, and 2110-2170MHz for downlink. The minimum allocation an operator needs is two paired 5MHz channels, one for uplink and one for downlink, at a separation of 190MHz. However, to provide

20、comprehensive coverage and services, it is recommended that an operator be given three channels. Considering the spectrum allocation, there are 12 paired channels available, and many countries have now completed the licencing process for this spectrum, allocating between two and four channels per li

21、cence. This has tended to work out a costly process for operators, since the regulatory authorities in some countries, notably in Europe, have auctioned these licences to the highest bidder. This has resulted in spectrum fees as high as tens of billions of dollars in some countries.The Time Division

22、 Duplex (TDD) system, which needs only one 5MHz band in which to operate, often referred to as unpaired spectrum. The differences between UMTS FDD and TDD are only evident at the lower layers, particularly on the radio interface. At higher layers, the bulk of the operation of the two systems is the

23、same. As the name suggests, the TDD system separates uplink and downlink traffic by placing them in different time slots. As will be seen later, UMTS uses a 10ms frame structure which is divided into 15 equal timeslots. TDD can allocate these to be either uplink or downlink,with one or more breakpoi

24、nts between the two in a frame defined. In this way, it is well suited to packet traffic, since this allows great flexibility in dynamically dimensioning for asymmetry in traffic flow.The TDD system should not really be considered as an independent network, but rather as a supplement for an FDD syst

25、em to provide hotspot coverage at higher data rates. It is rather unsuitable for large scale deployment due to interference between sites, since a BTS may be trying to detect a weak signal from a UE, which is blocked out by a relatively strong signal at the same frequency from a nearby BTS. TDD is i

26、deal for indoor coverage over small areas.Since FDD is the main access technology being developed currently, the explanations presented here will focus purely on this system.1.3 UMTS Bearer ModelThe procedures of a mobile device connecting to a UMTS network can be split into two areas: the access st

27、ratum (AS) and the non-access stratum (NAS). The access stratum involves all the layers and subsystems that offer general services to the non-access stratum. In UMTS, the access stratum consists of all of the elements in the radio access network, including the underlying ATM transport network, and t

28、he various mechanisms such as those to provide reliable information exchange. All of the non-access stratum functions are those between the mobile device and the core network, for example, mobility management. Figure 7 shows the architecture model. The AS interacts with the NAS through the use of se

29、rvice access points (SAPs).UMTS radio access network (UTRAN) provides this separation of NAS and AS functions, and allows for AS functions to be fully controlled and implemented within the UTRAN. The two major UTRAN interfaces are the Uu, which is the interface between the mobile device, or User Equ

30、ipment (UE) and the UTRAN, and the Iu, which is the interface between the UTRAN and the core network. Both of these interfaces can be divided into control and user planes each with appropriate protocol functions.A Bearer Service is a link between two points, which is defined by a certain set of char

31、acteristics. In the case of UMTS, the bearer service is delivered using radio access bearers.A Radio access bearer (RAB) is defined as the service that the access stratum (i.e.UTRAN) provides to the non-access stratum for transfer of user data between the User Equipment and Core Network. A RAB can c

32、onsist of a number of subflows, which are data streams to the core network within the RAB that have different QoS characteristics,such as different reliabilities. A common example of this is different classes of bits with different bit error rates can be realised as different RAB subflows. RAB subfl

33、ows are established and released at the time the RAB is established and released, and are delivered together over the same transport bearer.A Radio Link is defined as a logical association between a single User Equipment (UE) and a single UTRAN access point, such as an RNC. It is physically comprise

34、d of one or more radio bearers and should not be confused with radio access bearer.Looking within the UTRAN, the general architecture model is as shown in Figure 8 below. Now shown are the Node B or Base Station (BTS) and Radio Network Controller (RNC) components, and their respective internal inter

35、faces. The UTRAN is subdivided into blocks referred to as Radio Network Subsystems (RNS), where each RNS consists of one controlling RNC (CRNC) and all the BTSs under its control. Unique to UMTS is the interface between RNSs, the Iur interface, which plays a key role in handover procedures. The inte

36、rface between the BTS and RNC is the Iub interface.All the I interfaces: Iu, Iur and Iub, currently3 use ATM as a transport layer. In the context of ATM, the BTS is seen as a host accessing an ATM network, within which the RNC is an ATM switch. Therefore, the Iub is a UNI interface, whereas the Iu a

37、nd Iur interfaces are considered to be NNI, as illustrated in Figure 9.This distinction is because the BTS to RNC link is a point-to-point connection in that a BTS or RNC will only communicate with the RNC or BTS directly connected to it, and will not require communication beyond that element to ano

38、ther network element.For each user connection to the core network, there is only one RNC, which maintains the link between the UE and core network domain, as highlighted in Figure 10. This RNC is referred to as the serving RNC or SRNC. That SRNC plus the BTSs under its control is then referred to as

39、 the SRNS. This is a logical definition with reference to that UE only. In an RNS, the RNC that controls a BTS is known as the controlling RNC or CRNC. This is with reference to the BTS, cells under its control and all the common and shared channels within.As the UE moves, it may perform a soft or h

40、ard handover to another cell. In the case of a soft handover, the SRNC will activate the new connection to the new BTS. Should the new BTS be under the control of another RNC, the SRNC will also alert this new RNC to activate a connection along the Iur interface. The UE now has two links, one direct

41、ly to the SRNC, and the second, through the new RNC along the Iur interface. In this case, this new RNC is logically referred to as a drift RNC or DRNC, see Figure 10. It is not involved in any processing of the call and merely relays it to the SRNC for connection to the core. In summary, SRNC and D

42、RNC are usually associated with the UE and the CRNC is associated with the BTS. Since these are logical functions it is normal practice that a single RNC is capable of dealing with all these functions.A situation may arise where a UE is connected to a BTS for which the SRNC is not the CRNC for that

43、BTS. In that situation, the network may invoke the Serving RNC Relocation procedure to move the core network connection. This process is described inSection 3.通用移动通信系统的回顾1.1 UMTS网络架构欧洲/日本的3G标准，被称为UMTS。UMTS是一个在IMT-2000保护伞下的ITU-T批准的许多标准之一。随着美国的CDMA2000标准的发展，它是目前占主导地位的标准，特别是运营商将cdmaOne部署为他们的2G技术。在写这本书时

44、，日本是在3G网络部署方面最先进的。三名现任运营商已经实施了三个不同的技术：J - PHONE使用UMTS，KDDI拥有CDMA2000网络，最大的运营商NTT DoCoMo正在使用品牌的FOMA（自由多媒体接入）系统。 FOMA是基于原来的UMTS协议，而且更加的协调和标准化。UMTS标准被定义为一个通过通用分组无线系统（GPRS）和全球演进的增强数据技术（EDGE）从第二代GSM标准到UNTS的迁移。这是一个广泛应用的基本原理，因为自2003年4月起，全球有超过847万GSM用户，占全球的移动用户数字的68。重点是在保持尽可能多的GSM网络与新系统的操作。我们现在在第三代(3G)的发展道路

45、上，其中网络将支持所有类型的流量：语音，视频和数据，我们应该看到一个最终的爆炸在移动设备上的可用服务。此驱动技术是IP协议。现在，许多移动运营商在简称为2.5G的位置，伴随GPRS的部署，即将IP骨干网引入到移动核心网。SGSN和GGSN之间的接口被称为Gn接口和使用GPRS隧道协议（GTP的，稍后讨论）。引进这种基础设施的首要原因是提供连接到外部分组网络如，Internet或企业Intranet。这使IP协议作为SGSN和GGSN之间的运输工具应用到网络。这使得数据服务，如移动设备上的电子邮件或浏览网页，用户被起诉基于数据流量，而不是时间连接基础上的数据量。3G网络和服务交付的主要标准是通用

46、移动通信系统，或UMTS。首次部署的UMTS是发行99架构。在这个网络中，主要的变化是在无线接入网络（RAN的）CDMA空中接口技术的引进，和在传输部分异步传输模式作为一种传输方式。这些变化已经引入，主要是为了支持在同一网络上的语音，视频和数据服务的运输。核心网络保持相对不变，主要是软件升级。然而，随着目前无线网络控制器使用IP与3G的GPRS业务支持节点进行通信，IP协议进一步应用到网络。未来的进化步骤是第4版架构。在这里，GSM的核心被以语音IP技术为基础的IP网络基础设施取代。海安的发展分为两个独立部分：媒体网关（MGW）和MSC服务器（MSS）的。这基本上是打破外连接的作用和连接控制。

47、一个MSS可以处理多个MGW，使网络更具有扩展性。因为现在有一些在3G网络的IP云，合并这些到一个IP或IP/ ATM骨干网是很有意义的（它很可能会提供两种选择运营商）。这使IP权利拓展到整个网络，一直到BTS(基站收发信台)。这被称为全IP网络，或推出五架构，如图五所示。在HLR/ VLR/VLR/EIR被推广和称为HLR的子系统（HSS）。现在传统的电信交换的最后残余被删除，留下完全基于IP协议的网络运营，并推广了许多服务类型的运输。实时服务通过引入一个新的网络域名得到支持，即IP多媒体子系统（IMS）。目前3GPP作用于第6版，意在包含冷冻版本没有涵盖所有方面。有些人称UMTS 第6版为

48、4G和它包括热点无线电接入技术，如无线局域网互联互通的问题。1.2 UMTS的FDD和TDD像任何CDMA系统，UMTS需要一个宽的频带，在这个频带上有效地传播信号。该系统的特点是芯片的速度，芯片是一个符号的CDMA代码的宽度。 UMTS使用的芯片速率为3.84Mchips/秒，这转换到所需的频谱载波宽度为5MHz。由于这比现有的cdmaOne系统所需的1.25MHz带宽要宽，UNTS空中接口被称为“宽带”CDMA.实际上在UMTS下有两个无线电技术：UMTS软盘驱动器和时分双工。FDD代表频分双工，如GSM，通过把它们放置在不同的频率信道分离为交通上行和下行。因此，一个运营商必须有一对频率分

49、配，使他们能够运行网络，即术语成对频谱。TDD或时分双工只需要一个频率通道，上行和下行流量是在不同的时间分开发送。 ITU-T的频谱使用。对于FDD是1920 - 1980MHz的为上行流量，2110-2170MHz为下行的。运营商需要的最小分配是两个成对5MHz的信道，一个用于上行，一个用于下行的，两者相分离190MHz。然而，为了给客户提供全面的覆盖和服务，建议给予每个运营商三个信道。考虑到频谱分配，有12对可用的渠道，现在许多国家都完成了这个频谱的许可过程，每个许可证配置两个到四个信道。这趋向给运营商造成一个昂贵的花费，因为一些国家的监管部门，特别是在欧洲，已经将这些许可证拍卖给出价最高的人。这就造成了频谱费用在一些国家高达数十亿美元。时分双工（TDD）系统，只需要一个5MHz的带宽在其中操作，通常被称为非成对频谱。UMTS FDD和TDD之间的差异只有在较低层明显，特别是在无线接口。在更高的层次，两个系统的运作大部分是相同的。正如它的名字表明，TDD系统通过把它们放置在不同的时间空挡分为上行流量和下行流